|
NAME | SYNOPSIS | CONFIGURATION | DESCRIPTION | FILES | SEE ALSO | COLOPHON |
LP(4) Linux Programmer's Manual LP(4)
lp - line printer devices
#include <linux/lp.h>
lp[0–2] are character devices for the parallel line printers; they
have major number 6 and minor number 0–2. The minor numbers
correspond to the printer port base addresses 0x03bc, 0x0378 and
0x0278. Usually they have mode 220 and are owned by root and group
lp. You can use printer ports either with polling or with
interrupts. Interrupts are recommended when high traffic is
expected, for example, for laser printers. For typical dot matrix
printers, polling will usually be enough. The default is polling.
The following ioctl(2) calls are supported:
int ioctl(int fd, LPTIME, int arg)
Sets the amount of time that the driver sleeps before
rechecking the printer when the printer's buffer appears to be
filled to arg. If you have a fast printer, decrease this
number; if you have a slow printer, then increase it. This is
in hundredths of a second, the default 2 being 0.02 seconds.
It influences only the polling driver.
int ioctl(int fd, LPCHAR, int arg)
Sets the maximum number of busy-wait iterations which the
polling driver does while waiting for the printer to get ready
for receiving a character to arg. If printing is too slow,
increase this number; if the system gets too slow, decrease
this number. The default is 1000. It influences only the
polling driver.
int ioctl(int fd, LPABORT, int arg)
If arg is 0, the printer driver will retry on errors,
otherwise it will abort. The default is 0.
int ioctl(int fd, LPABORTOPEN, int arg)
If arg is 0, open(2) will be aborted on error, otherwise error
will be ignored. The default is to ignore it.
int ioctl(int fd, LPCAREFUL, int arg)
If arg is 0, then the out-of-paper, offline and error signals
are required to be false on all writes, otherwise they are
ignored. The default is to ignore them.
int ioctl(int fd, LPWAIT, int arg)
Sets the number of busy waiting iterations to wait before
strobing the printer to accept a just-written character, and
the number of iterations to wait before turning the strobe off
again, to arg. The specification says this time should be 0.5
microseconds, but experience has shown the delay caused by the
code is already enough. For that reason, the default value is
0. This is used for both the polling and the interrupt
driver.
int ioctl(int fd, LPSETIRQ, int arg)
This ioctl(2) requires superuser privileges. It takes an int
containing the new IRQ as argument. As a side effect, the
printer will be reset. When arg is 0, the polling driver will
be used, which is also default.
int ioctl(int fd, LPGETIRQ, int *arg)
Stores the currently used IRQ in arg.
int ioctl(int fd, LPGETSTATUS, int *arg)
Stores the value of the status port in arg. The bits have the
following meaning:
LP_PBUSY inverted busy input, active high
LP_PACK unchanged acknowledge input, active low
LP_POUTPA unchanged out-of-paper input, active high
LP_PSELECD unchanged selected input, active high
LP_PERRORP unchanged error input, active low
Refer to your printer manual for the meaning of the signals.
Note that undocumented bits may also be set, depending on your
printer.
int ioctl(int fd, LPRESET)
Resets the printer. No argument is used.
/dev/lp*
chmod(1), chown(1), mknod(1), lpcntl(8), tunelp(8)
This page is part of release 4.12 of the Linux man-pages project. A
description of the project, information about reporting bugs, and the
latest version of this page, can be found at
https://www.kernel.org/doc/man-pages/.
Linux 1995-01-15 LP(4)