FCLOSE
Section: POSIX Programmer's Manual (3P)
Updated: 2017
Index
Return to Main Contents
PROLOG
This manual page is part of the POSIX Programmer's Manual.
The Linux implementation of this interface may differ (consult
the corresponding Linux manual page for details of Linux behavior),
or the interface may not be implemented on Linux.
NAME
fclose
--- close a stream
SYNOPSIS
#include <stdio.h>
int fclose(FILE *stream);
DESCRIPTION
The functionality described on this reference page is aligned with the
ISO C standard. Any conflict between the requirements described here and the
ISO C standard is unintentional. This volume of POSIX.1-2017 defers to the ISO C standard.
The
fclose()
function shall cause the stream pointed to by
stream
to be flushed and the associated file to be closed. Any unwritten
buffered data for the stream shall be written to the file; any unread
buffered data shall be discarded. Whether or not the call succeeds,
the stream shall be disassociated from the file and any buffer set by
the
setbuf()
or
setvbuf()
function shall be disassociated from the stream. If the associated
buffer was automatically allocated, it shall be deallocated.
If the file is not already at EOF, and the file is one capable of seeking,
the file offset of the underlying open file description shall be set to
the file position of the stream if the stream is the active handle to
the underlying file description.
The
fclose()
function shall mark for update the last data modification and last
file status change timestamps of the underlying file, if the stream was
writable, and if buffered data remains that has not yet been written to
the file. The
fclose()
function shall perform the equivalent of a
close()
on the file descriptor that is associated with the stream pointed to by
stream.
After the call to
fclose(),
any use of
stream
results in undefined behavior.
RETURN VALUE
Upon successful completion,
fclose()
shall return 0; otherwise, it shall return EOF
and set
errno
to indicate the error.
ERRORS
The
fclose()
function shall fail if:
- EAGAIN
-
The O_NONBLOCK flag is set for the file descriptor underlying
stream
and the thread would be delayed in the write operation.
- EBADF
-
The file descriptor underlying stream is not valid.
- EFBIG
-
An attempt was made to write a file that exceeds the maximum file size.
- EFBIG
-
An attempt was made to write a file that exceeds the file size
limit of the process.
- EFBIG
-
The file is a regular file and an attempt was made to write at or beyond
the offset maximum associated with the corresponding stream.
- EINTR
-
The
fclose()
function was interrupted by a signal.
- EIO
-
The process is a member of a background process group attempting to
write to its controlling terminal, TOSTOP is set, the calling thread
is not blocking SIGTTOU, the process is not ignoring SIGTTOU, and the
process group of the process is orphaned.
This error may also be returned under implementation-defined conditions.
- ENOMEM
-
The underlying stream was created by
open_memstream()
or
open_wmemstream()
and insufficient memory is available.
- ENOSPC
-
There was no free space remaining on the device containing the file or
in the buffer used by the
fmemopen()
function.
- EPIPE
-
An attempt is made to write to a pipe or FIFO that is not open for
reading by any process. A SIGPIPE signal shall also be sent to the
thread.
The
fclose()
function may fail if:
- ENXIO
-
A request was made of a nonexistent device, or the request was outside
the capabilities of the device.
The following sections are informative.
EXAMPLES
None.
APPLICATION USAGE
Since after the call to
fclose()
any use of
stream
results in undefined behavior,
fclose()
should not be used on
stdin,
stdout,
or
stderr
except immediately before process termination (see the Base Definitions volume of POSIX.1-2017,
Section 3.303, Process Termination),
so as to avoid triggering undefined behavior in other standard
interfaces that rely on these streams. If there are any
atexit()
handlers registered by the application, such a call to
fclose()
should not occur until the last handler is finishing. Once
fclose()
has been used to close
stdin,
stdout,
or
stderr,
there is no standard way to reopen any of these streams.
Use of
freopen()
to change
stdin,
stdout,
or
stderr
instead of closing them avoids the danger of a file unexpectedly
being opened as one of the special file descriptors STDIN_FILENO,
STDOUT_FILENO, or STDERR_FILENO at a later time in the application.
RATIONALE
None.
FUTURE DIRECTIONS
None.
SEE ALSO
Section 2.5, Standard I/O Streams,
atexit(),
close(),
fmemopen(),
fopen(),
freopen(),
getrlimit(),
open_memstream(),
ulimit()
The Base Definitions volume of POSIX.1-2017,
<stdio.h>
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form
from IEEE Std 1003.1-2017, Standard for Information Technology
-- Portable Operating System Interface (POSIX), The Open Group Base
Specifications Issue 7, 2018 Edition,
Copyright (C) 2018 by the Institute of
Electrical and Electronics Engineers, Inc and The Open Group.
In the event of any discrepancy between this version and the original IEEE and
The Open Group Standard, the original IEEE and The Open Group Standard
is the referee document. The original Standard can be obtained online at
http://www.opengroup.org/unix/online.html .
Any typographical or formatting errors that appear
in this page are most likely
to have been introduced during the conversion of the source files to
man page format. To report such errors, see
https://www.kernel.org/doc/man-pages/reporting_bugs.html .
Index
- PROLOG
-
- NAME
-
- SYNOPSIS
-
- DESCRIPTION
-
- RETURN VALUE
-
- ERRORS
-
- EXAMPLES
-
- APPLICATION USAGE
-
- RATIONALE
-
- FUTURE DIRECTIONS
-
- SEE ALSO
-
- COPYRIGHT
-
This document was created by
man2html,
using the manual pages.
Time: 06:23:07 GMT, May 09, 2021