Skip Headers
Oracle® OLAP DML Reference
11g Release 2 (11.2)

Part Number E17122-07
Go to Documentation Home
Home
Go to Book List
Book List
Go to Table of Contents
Contents
Go to Index
Index
Go to Master Index
Master Index
Go to Feedback page
Contact Us

Go to previous page
Previous
Go to next page
Next
PDF · Mobi · ePub

SWITCH command

The SWITCH command provides a multipath branch in a program. The specific path taken during program execution depends on the value of the control expression that is specified with SWITCH. You can use a SWITCH statement only within programs.

Note:

Do not confuse the use of a single SWITCH command with the use of SWTICH as a conditional operator in an expression. See "SWITCH Expressions".

Syntax

SWITCH control-expression

   DO

      CASE case-expression1:

          statement 1.1

           ...

          statement 1.n

           BREAK

      CASE case-expression2:

           statement 2.1

           ...

           statement 2.n

           BREAK

      [DEFAULT:

           statement n.1

           ...

           statement n.n

           BREAK]

   DOEND

Parameters

control-expression

The control-expression argument determines the case label to which program control is transferred by the SWITCH statement. When the SWITCH statement is executed, control-expression is evaluated and compared with each of the CASE label expressions in the program. When a match is found, control is transferred to that case label. When no match is found, control transfers to the DEFAULT label (if present) or to the statement following the DOEND for SWITCH.

CASE case-expression1, CASE case-expression2, ...

The CASE labels whose expressions (case-expression1, case-expression2, ...) specify the different cases you want to handle. When control-expression matches case-expression, program control is transferred to that CASE label. The CASE label expressions are evaluated at the time the program is run, in the order they appear, until a match is found.

The DEFAULT label is optional. It identifies a special case to which control should be transferred when none of the case-expressions matches the control-expression. When you omit DEFAULT, and no match is found, control is transferred to the statement that follows the DOEND for SWITCH.

All the CASE labels (including DEFAULT) for a SWITCH statement must be included within a DO/DOEND bracket immediately following the SWITCH statement. Because case-expression is a label, it must be followed by a colon (:). The statements to be executed in a given case must follow the label. Normally, the last statement in a case should be BREAK, which transfers control from SWITCH to the statement that follows the DOEND for SWITCH.

When you omit BREAK (or RETURN, SIGNAL, and so on) at the end of a case, the program goes on to execute the statements for the next case as well. Normally, you do not want this to happen. However, when you plan to execute the same statements for two cases, you can use this to your advantage by placing both CASE labels before the statements.

Usage Notes

Control and Case Expressions

The SWITCH control-expression can have any data type, as can the case-expressions. The various case-expressions can have different data types. When you specify the name of a dimension (as a literal, non-quoted text expression) as the control-expression or case-expression, Oracle OLAP uses the first value in the dimension's current status list, not the dimension name, as it searches for a match. When the dimension has no values in the status list, Oracle OLAP uses the value NA. An NA control-expression matches the first NA case-expression.

Do Not Use Ampersand Substitution with SWITCH

Avoid using ampersand substitution in a SWITCH control-expression or in a CASE label case-expression. Ampersands produce unpredictable, and usually undesirable, results.

Multiple SWITCH Commands

You can include multiple SWITCH statements in a program. You can also nest SWITCH commands. When a program contains multiple SWITCH commands, each can have its own DEFAULT label, even when the SWITCH commands are nested.

Transferring Control

While BREAK is commonly used to transfer program control within a SWITCH statement, it is not the only such statement you can use. You can also use statements such as CONTINUE, GOTO, RETURN, and SIGNAL. Keep in mind that you can use CONTINUE only when the SWITCH statement is within a FOR or WHILE loop. See also the entries for these statements and for DO ... DOEND.

Examples

Example 10-153 Multipath Branching Using SWITCH in a Program

The following program lines produce one of several types of reports. Before the SWITCH statement, the program determines which type of report the user wants and places the value Market or Finance in the variable userchoice. The program switches to the case label that matches that name and produces the report. When the report finishes, the BREAK statement transfers control to the cleanup section after the DOEND.

SWITCH userchoice
    DO
         CASE 'Market':
            ...
            BREAK
         CASE 'Finance':
            ...
            BREAK
         DEFAULT:
            ...
            BREAK
    DOEND
cleanup:
...