SuperH Interfaces Guide¶

Author:	Paul Mundt

Memory Management¶

SH-4¶

Store Queue API¶

void sq_flush_range(unsigned long start, unsigned int len)¶: Flush (prefetch) a specific SQ range

Parameters

unsigned long start: the store queue address to start flushing from
unsigned int len: the length to flush

Description

Flushes the store queue cache from start to start + len in a linear fashion.

unsigned long sq_remap(unsigned long phys, unsigned int size, const char * name, pgprot_t prot)¶: Map a physical address through the Store Queues

Parameters

unsigned long phys: Physical address of mapping.
unsigned int size: Length of mapping.
const char * name: User invoking mapping.
pgprot_t prot: Protection bits.

Description

Remaps the physical address phys through the next available store queue address of size length. name is logged at boot time as well as through the sysfs interface.

void sq_unmap(unsigned long vaddr)¶: Unmap a Store Queue allocation

Parameters

unsigned long vaddr: Pre-allocated Store Queue mapping.

Description

Unmaps the store queue allocation map that was previously created by sq_remap(). Also frees up the pte that was previously inserted into the kernel page table and discards the UTLB translation.

SH-5¶

TLB Interfaces¶

int sh64_tlb_init(void)¶: Perform initial setup for the DTLB and ITLB.

Parameters

void: no arguments

unsigned long long sh64_next_free_dtlb_entry(void)¶: Find the next available DTLB entry

Parameters

void: no arguments

unsigned long long sh64_get_wired_dtlb_entry(void)¶: Allocate a wired (locked-in) entry in the DTLB

Parameters

void: no arguments

int sh64_put_wired_dtlb_entry(unsigned long long entry)¶: Free a wired (locked-in) entry in the DTLB.

Parameters

unsigned long long entry: Address of TLB slot.

Description

Works like a stack, last one to allocate must be first one to free.

void sh64_setup_tlb_slot(unsigned long long config_addr, unsigned long eaddr, unsigned long asid, unsigned long paddr)¶: Load up a translation in a wired slot.

Parameters

unsigned long long config_addr: Address of TLB slot.
unsigned long eaddr: Virtual address.
unsigned long asid: Address Space Identifier.
unsigned long paddr: Physical address.

Description

Load up a virtual<->physical translation for eaddr**<->**paddr in the pre-allocated TLB slot config_addr (see sh64_get_wired_dtlb_entry).

void sh64_teardown_tlb_slot(unsigned long long config_addr)¶: Teardown a translation.

Parameters

unsigned long long config_addr: Address of TLB slot.

Description

Teardown any existing mapping in the TLB slot config_addr.

for_each_dtlb_entry(tlb)¶: Iterate over free (non-wired) DTLB entries

Parameters

tlb: TLB entry

for_each_itlb_entry(tlb)¶: Iterate over free (non-wired) ITLB entries

Parameters

tlb: TLB entry

void __flush_tlb_slot(unsigned long long slot)¶: Flushes TLB slot slot.

Parameters

unsigned long long slot: Address of TLB slot.

Machine Specific Interfaces¶

mach-dreamcast¶

int aica_rtc_gettimeofday(struct device * dev, struct rtc_time * tm)¶: Get the time from the AICA RTC

Parameters

struct device * dev: the RTC device (ignored)
struct rtc_time * tm: pointer to resulting RTC time structure

Description

Grabs the current RTC seconds counter and adjusts it to the Unix Epoch.

int aica_rtc_settimeofday(struct device * dev, struct rtc_time * tm)¶: Set the AICA RTC to the current time

Parameters

struct device * dev: the RTC device (ignored)
struct rtc_time * tm: pointer to new RTC time structure

Description

Adjusts the given tv to the AICA Epoch and sets the RTC seconds counter.

mach-x3proto¶

int ilsel_enable(ilsel_source_t set)¶: Enable an ILSEL set.

Parameters

ilsel_source_t set: ILSEL source (see ilsel_source_t enum in include/asm-sh/ilsel.h).

Description

Enables a given non-aliased ILSEL source (<= ILSEL_KEY) at the highest available interrupt level. Callers should take care to order callsites noting descending interrupt levels. Aliasing FPGA and external board IRQs need to use ilsel_enable_fixed().

The return value is an IRQ number that can later be taken down with ilsel_disable().

int ilsel_enable_fixed(ilsel_source_t set, unsigned int level)¶: Enable an ILSEL set at a fixed interrupt level

Parameters

ilsel_source_t set: ILSEL source (see ilsel_source_t enum in include/asm-sh/ilsel.h).
unsigned int level: Interrupt level (1 - 15)

Description

Enables a given ILSEL source at a fixed interrupt level. Necessary both for level reservation as well as for aliased sources that only exist on special ILSEL#s.

Returns an IRQ number (as ilsel_enable()).

void ilsel_disable(unsigned int irq)¶: Disable an ILSEL set

Parameters

unsigned int irq: Bit position for ILSEL set value (retval from enable routines)

Description

Disable a previously enabled ILSEL set.

Busses¶

SuperHyway¶

int superhyway_add_device(unsigned long base, struct superhyway_device * sdev, struct superhyway_bus * bus)¶: Add a SuperHyway module

Parameters

unsigned long base: Physical address where module is mapped.
struct superhyway_device * sdev: SuperHyway device to add, or NULL to allocate a new one.
struct superhyway_bus * bus: Bus where SuperHyway module resides.

Description

This is responsible for adding a new SuperHyway module. This sets up a new struct superhyway_device for the module being added if sdev == NULL.

Devices are initially added in the order that they are scanned (from the top-down of the memory map), and are assigned an ID based on the order that they are added. Any manual addition of a module will thus get the ID after the devices already discovered regardless of where it resides in memory.

Further work can and should be done in superhyway_scan_bus(), to be sure that any new modules are properly discovered and subsequently registered.

int superhyway_register_driver(struct superhyway_driver * drv)¶: Register a new SuperHyway driver

Parameters

struct superhyway_driver * drv: SuperHyway driver to register.

Description

This registers the passed in drv. Any devices matching the id table will automatically be populated and handed off to the driver’s specified probe routine.

void superhyway_unregister_driver(struct superhyway_driver * drv)¶: Unregister a SuperHyway driver

Parameters

struct superhyway_driver * drv: SuperHyway driver to unregister.

Description

This cleans up after superhyway_register_driver(), and should be invoked in the exit path of any module drivers.

Maple¶

int maple_driver_register(struct maple_driver * drv)¶: register a maple driver

Parameters

struct maple_driver * drv: maple driver to be registered.

Description

Registers the passed in drv, while updating the bus type. Devices with matching function IDs will be automatically probed.

void maple_driver_unregister(struct maple_driver * drv)¶: unregister a maple driver.

Parameters

struct maple_driver * drv: maple driver to unregister.

Description

Cleans up after maple_driver_register(). To be invoked in the exit path of any module drivers.

void maple_getcond_callback(struct maple_device * dev, void (*callback) (struct mapleq *mq, unsigned long interval, unsigned long function)¶: setup handling MAPLE_COMMAND_GETCOND

Parameters

struct maple_device * dev: device responding
void (*) (struct mapleq *mq) callback: handler callback
unsigned long interval: interval in jiffies between callbacks
unsigned long function: the function code for the device

int maple_add_packet(struct maple_device * mdev, u32 function, u32 command, size_t length, void * data)¶: add a single instruction to the maple bus queue

Parameters

struct maple_device * mdev: maple device
u32 function: function on device being queried
u32 command: maple command to add
size_t length: length of command string (in 32 bit words)
void * data: remainder of command string